Home › Set up a launch monitor › How to Set Up a Launch Monitor Indoors

Reviewed The Golf Sim Guide desk

Set up a launch monitor

How to Set Up a Launch Monitor Indoors: Distances, Alignment, Light and Balls

A launch monitor that reads 150 yards outdoors can read nonsense in a garage, and the cause is almost never the unit. It sits 3 ft too close to the wall, or faces the sun through a door, or has no marked ball to read spin from. The makers write down what their units need, and the rear distance alone differs by 4 ft or more from one brand to the next. We went through the makers' manuals and guides and turned them into one order of work: measure, place, aim, light, mark the ball, then hit ten shots. Room figures and yearly plan prices are quoted only where a maker prints them.

Quick read

For how to set up a launch monitor indoors in one sentence: measure 14 to 16 ft of depth for a radar unit, set it 4 to 8.5 ft behind the ball on the target line, keep the ball at least 8 ft from the net, and keep direct sun off the front of the unit. A camera unit goes about 1.5 to 2 ft beside the ball instead. Mark the ball or the club if your maker asks for it, then hit ten shots with one club before you trust any number.

Three picks for three rooms: the right answer starts with the ceiling and the depth behind the ball, not with the box.

🥇The unit with the plainest setup: 8 ft behind the ball, 8 ft to the net, 16 ft in all, 43 of 60

FlightScope Mevo Gen2

43/60our score

Both indoor distances are written by the maker: 8 ft behind the ball and 8 ft to the net, so the setup has no guesswork

Its catch: The Mevo Gen2 asks the longest bay of the three, and FlightScope warns that under 16 ft tracking can be inaccurate.

🥈The unit that adds swing video to the placement: 6.5 to 8.5 ft behind, 8 ft to the net, 38 of 60

Rapsodo MLM2PRO

38/60our score

Rapsodo publishes both distances: 6.5 to 8.5 ft behind the ball and 8 ft to the net

Its catch: Spin indoors needs an RPT ball and, for four readings, a Rapsodo membership.

🥉The shortest rear distance of the three: 6 to 8 ft behind the ball, 14 to 16 ft of depth, 38 of 60

Garmin Approach R10

38/60our score

The widest window of the three: 6 to 8 ft behind the tee, so the unit has 2 ft of play

Its catch: Garmin writes no ceiling height for the R10, so the room check rests on the 48 in rule or another maker's figure.

How to Set Up a Launch Monitor Indoors: Distances, Alignment, Light and Balls
Illustration

Which unit to set up first, by the depth you can measure

  • Take it if you have a full 16 ft of depth and want the placement spelled out: FlightScope Mevo Gen2 43/60
  • Take it if you have 14 to 16 ft and want the smallest rear distance of the three: Garmin Approach R10 38/60
  • Take it if you have a little over 14 ft and want a unit that also films the swing: Rapsodo MLM2PRO 38/60

The golden rule: Measure the floor first: 16 ft of depth fits all three units below, 14 ft fits the Garmin R10 and, by the maker's own sum, the Rapsodo MLM2PRO.

Good to know: the links to Amazon.com are affiliate links: a purchase after a click can earn this site a commission, at no cost to you. Nothing was set up by the desk; n.p. marks a figure the maker does not state. As an Amazon Associate I earn from qualifying purchases.
Contents9 sections
  1. 01What do you need before you set up a launch monitor indoors?
  2. 02Where does the launch monitor go: behind the ball or beside it?
  3. 03How do you set up a golf simulator indoors, step by step?
  4. 04How do I set up my Garmin Approach R10 indoors?
  5. 05How do you set up the other units, and who needs stickers or special balls?
  6. 06How do you light the room and keep other electronics from disturbing the unit?
  7. 07How do you use a golf launch monitor in a session, once it is set up?
  8. 08Questions about how to set up a launch monitor indoors
  9. 09Sources

What do you need before you set up a launch monitor indoors?

How to set up a launch monitor indoors is a job of placing one small box inside a room that has been measured, and it starts before the box comes out of its case. You need a floor you have measured, a net or screen that stops the ball, a hitting surface, the markers your unit asks for, and a phone or computer for the app. A phone is the screen, not the sensor: whether it can replace the unit is answered in our no-net launch monitor guide. Skip any of the five and the first session ends early, usually in the first ten shots. Which unit to buy is a different question: the best indoor launch monitor page ranks the units, and the home simulator page covers the best indoor golf simulator as a whole room. This page assumes the unit is already in the box.

Start with numbers, not equipment. Our room rule is your height in inches plus 48 in for the ceiling, so a 6 ft golfer needs 72 in + 48 in = 120 in, or 10 ft. The makers sit close to it: FlightScope gives 9 ft as the minimum and 10 to 12 ft as ideal, Rapsodo says most indoor simulators need 9 ft and taller players 10 or 11 ft, and SkyTrak calls 10 ft ample while noting that many golfers say 9 ft is enough. The room size calculator turns your own measurements into a pass or fail.

  • Depth: 14 to 16 ft for a radar, where the maker writes both distances.
  • Width: 12 ft is the figure FlightScope and SkyTrak both suggest; Bushnell writes at least 6 ft for its camera unit.
  • A net or screen: tall and wide enough for high shots, with free space behind it and a padded frame, as Garmin and Shot Scope both write.
  • A hitting surface: a mat, with the unit's bottom edge level with or above it where the maker says so.
  • Markers: stickers, a marked ball or a club sticker, depending on the brand (table below).

Where does the launch monitor go: behind the ball or beside it?

A radar unit goes on the floor behind the ball, on the target line, 4 to 8.5 ft back; a camera unit goes beside the ball, about 1.5 to 2 ft away. Everything else in the room follows from that choice, and the radar vs camera guide explains why.

UnitWhere the unit goesBall to netDepth by our additionWhat it means
Shot Scope LM14 to 5 ft (1.4 m) behindNot writtenNot writtenThe shortest rear distance of the radars
Voice Caddie SC4 PRO4.5 to 5 ft behind10 ft advised, 9 ft minimum13.5 to 15 ftMove to 4 ft for irons if the maker's FAQ applies
Garmin Approach R106 to 8 ft behindAt least 8 ft indoors14 to 16 ftHitting area starts 6 ft from the unit
Rapsodo MLM2PRO6.5 to 8.5 ft behind8 ft14.5 to 16.5 ftRapsodo writes a little more than 14 ft
FlightScope Mevo Gen28 ft behind (7 to 9 ft on one page)8 ft16 ftRapsodo and Garmin write the same 8 ft to the net
Garmin Approach R50About 1.5 ft beside the teeNot writtenNot writtenNothing stands behind the ball
Bushnell Launch ProAbout 2 ft besideNot written13 ft deep, 6 ft wideRaise it to the height of the mat
SkyTrakNext to the ballNot written15 to 17 ft in a studio planSkyTrak's figures describe its studio sizes

Two warnings come with the table. The two Rapsodo sums differ because Rapsodo writes "a little more than 14 total feet" while adding its own two ranges gives 14.5 to 16.5 ft; plan on the larger one. And the Mevo Gen2 has two wordings, 8 ft behind the ball in the indoor guide and 7 to 9 ft from sensor to tee on the product page, so measure 8 ft and leave 1 ft of play behind it.

4 to 8.5 ftrear distance of the radar units

Shot Scope LM1 up to Rapsodo MLM2PRO

8 ftball to net

the figure Garmin, Rapsodo and FlightScope share

1.5 to 2 ftcamera unit beside the ball

Garmin R50 and Bushnell Launch Pro

Sources: Garmin, Approach R10 owner's manual ; Rapsodo, golf FAQ ; FlightScope, indoor use guide ; Voice Caddie, FAQ

How do you set up a golf simulator indoors, step by step?

The steps for how to set up a launch monitor indoors are the same for every brand, and only the numbers change. Measure, mark the tee, place the unit, aim it, build the net line, light the room, then run a ten-shot check. The order matters because each step uses the number from the one before it.

  1. 1
    1. Mark the tee

    Put a strip of tape where the ball will sit. Every distance below is measured from that spot, not from the mat's edge.

  2. 2
    2. Measure to the net

    From the tee spot to the net or screen, at least 8 ft for the R10, the MLM2PRO and the Mevo Gen2, 10 ft advised for the SC4 PRO.

  3. 3
    3. Measure behind

    From the tee spot back to the wall: 4 to 8.5 ft for a radar, nothing for a camera unit.

  4. 4
    4. Place the unit

    On the floor, on the target line, level with the hitting surface. With a mat, the unit's bottom edge sits at or above it, as Garmin and Bushnell write.

  5. 5
    5. Aim it

    A radar faces down the target line from behind the ball. A camera unit faces the tee spot from the side.

  6. 6
    6. Pad and size the net

    High enough and wide enough for a high-lofted or errant shot, with space behind it and a padded frame, per Garmin and Shot Scope.

  7. 7
    7. Control the light

    Direct sun off the front of the unit; a projector, if you add one, wants controlled light.

  8. 8
    8. Run ten shots

    One club, one ball type, same spot. The numbers should repeat before you compare anything.

Whatever your brand, how to set up a launch monitor indoors comes down to two rules that save most setups. Do the measuring with a tape, not by pacing, because 1 ft of error at the rear of an 8 ft window is a 12 percent error. And finish the room before you buy a projector: the simulator room guide and the low-ceiling page show what still works in a short bay.

Lesson learned : a 6 ft golfer with a Garmin R10 in a garage

The garage is 17 ft deep and 9 ft 6 in to the ceiling. The golfer is 72 in tall, so our rule asks for 120 in, or 10 ft, and the garage is 6 in short; a 9 ft ceiling is what several makers call workable, so the golfer takes slow driver swings first. Tee spot 9 ft from the net, which clears Garmin's 8 ft minimum by 1 ft. The R10 sits 7 ft behind the tee, in the middle of Garmin's 6 to 8 ft window, so the garage needs 9 + 7 = 16 ft before the net frame, and 1 ft is left over.

How do I set up my Garmin Approach R10 indoors?

Put the R10 on the floor 6 to 8 ft behind the tee, keep the tee at least 8 ft from the net, keep the unit's bottom edge above the mat, and keep the front out of direct sun. That is Garmin's own wording for indoor play, and the numbers add up to 14 to 16 ft.

What do you do, in order, with the R10?

Here is how to set up a launch monitor indoors with the R10, following Garmin's own order:

  1. Fix the tee spot and measure 8 ft or more to the net.
  2. Put the unit on the ground 6 to 8 ft behind the tee, in line with the target. The R10 has a tripod stand and a phone mount in the box if you want the screen at eye level.
  3. If you hit from a mat, raise the unit so its bottom edge sits above the mat.
  4. Stand so the ball falls inside the 2 x 2 ft hitting area that begins 6 ft from the unit; the ball cannot sit closer than 6 ft.
  5. Open the Garmin Golf app, pick a practice mode and hit. Virtual rounds on the 43,000 courses Garmin counts need a Garmin Golf membership.

Garmin writes three safety lines for the room itself: enough ceiling height, a net or screen with free space behind it and tall enough for high shots, and a padded frame to cut ricochet. The manual gives no ceiling number, so use our 48 in rule or SkyTrak's, FlightScope's and Rapsodo's figures from above. The Garmin R10 review shows the scores and the room math in one place.

How do you use the Garmin R10 launch monitor once it is placed?

Use the app's training mode, hit ten shots with one club, and read ball speed and launch angle first. Garmin prints tolerances of plus or minus 1 mph on ball speed, 3 mph on club head speed and 1 degree on launch angle and direction, without saying under what conditions. A 1 mph error is 0.7 percent of a 150 mph shot, so a 2 mph gap between two shots is your swing and not the unit.

How do you set up the other units, and who needs stickers or special balls?

The Mevo Gen2 and the MLM2PRO read spin indoors only with the maker's marked ball or sticker, and the R50 needs a club sticker for face to path. Marking is the part of the setup people skip, and it is the reason spin reads zero in a room.

UnitWhat it needs for spin or face dataWhere the maker writes itWhat it means
FlightScope Mevo Gen2Aluminum stickers or Titleist RCT ballsIndoor use guide100 stickers come with the unit
Rapsodo MLM2PROAn RPT ball, in Net modeFAQ3 RPT balls in the box
Garmin Approach R50The included club sticker for face to pathManualDirect sun on the club face spoils it
Garmin Approach R10A club sticker, if you use itManualKeep sun off the club face too

Where does a SkyTrak go, and what room does SkyTrak write?

SkyTrak places its unit next to the ball, not behind it, and says other launch monitors need up to 8 ft behind the hitting area. The pages we read give no distance in feet from the ball to the unit, so follow the app's placement screen. What SkyTrak does write is the room: a 10 ft ceiling gives ample clearance for most golfers, 9 ft is enough for many, 12 ft of width is suggested and 17 ft of depth is called comfortable. SkyTrak also offers a "Driver Test", a slow driver swing in the room before you buy anything. Do the same with a broom handle and a tape measure before you cut a net.

How do you set up the Mevo Gen2 and the Rapsodo MLM2PRO?

For the Mevo Gen2, FlightScope says to put the unit 8 ft directly behind the ball, with at least 16 ft of total depth, and warns that less can give inaccurate tracking. It adds that noisy electronics such as an air conditioner, a television or a fan belong behind the unit, not between it and the ball. For the MLM2PRO, Rapsodo says the unit sits 6.5 to 8.5 ft directly behind the ball, aimed down the target line, with 8 ft from ball to net, and that taller players may need to stand it further back to capture the whole swing video. A tripod comes in the box for that spot.

How do you use a Rapsodo launch monitor?

Open Session Setup and choose Net when you hit into a net, indoors or outdoors, or Range for the full ball flight outside. Practice mode is free with a registered device and shows carry distance and ball speed on every shot. Spin rate, spin axis, attack angle and club path need a membership, Core at $199.99 a year or Studios at $399.99, and spin is shown only in Net mode with an RPT ball. The Rapsodo MLM2PRO review lists what each plan unlocks.

How do you use a PRGR launch monitor?

The HS 130-A product page on Amazon.com says it needs no app, calibration or subscription, runs on AAA batteries, stores 500 swings and reads club head speed with or without a ball. It gives no placement distance, so we cannot tell you where to set it. Read the card in the box for the distance, and treat the carry and total numbers as estimates, since the page marks them as estimated and not measured. See the PRGR HS 130-A review.

How do you light the room and keep other electronics from disturbing the unit?

Keep direct sun off the front of the unit, keep noisy electronics behind it, and keep other radio devices away from a radar. Light matters for cameras and for any unit facing a window; radio noise matters for radars.

Garmin writes that direct sunlight on the front of the R10 or the R50 can cause misreads, and that a low sun in front of the R10 is the worst case. The same manual asks you to keep sun off the club face when you use the sticker. A radar can be disturbed by radio: Shot Scope says a computer, another launch monitor or any radio device near the LM1 can give wrong readings, and the unit is a 24 GHz Doppler radar. FlightScope's advice is the practical version, noisy electronics behind the unit.

If you add a portable projector, check its battery. The U.S. Consumer Product Safety Commission recalled the BenQ GV31 portable projector on July 30, 2026 (recall 26-647) because its lithium-ion battery can overheat, and the remedy is a free battery repair or a replacement projector. On projectors, Foresight Sports recommends a short-throw model with at least 3,000 lumens and writes that the projector needs controlled lighting for a clear image. That is about the screen, not the launch monitor. For every other maker, we found no lighting figure, so we claim none.

Unit or partWhat disturbs itWhat the maker writesWhat it means
Garmin Approach R10Direct sun on the front, a low sun facing it, sun on the club faceMinimize the sunlight on bothTurn the unit or block the window
Garmin Approach R50Direct sun on the frontMinimize the sunlightSame fix as the R10
Shot Scope LM1Computers, other launch monitors, other radio devicesWrong readings are possible near them; no distance is writtenKeep a second unit or a laptop away from the radar
FlightScope Mevo Gen2Air conditioner, television, computer, fan, refrigeratorPut noisy electronics behind the unitNothing noisy between the unit and the ball
Projector, any simulatorAmbient light on the screenAt least 3,000 lumens and controlled lighting (Foresight)A screen question, not a launch monitor one

Worth knowing

Put the unit where the sun cannot reach its front at the time you usually play. A low winter sun through a garage door is the case Garmin names, and the fix is blocking the window or turning the unit, not buying a different launch monitor.

How do you use a golf launch monitor in a session, once it is set up?

Hit ten shots with one club and one ball, drop the worst, average the rest, and repeat on a second day before you compare clubs. A session that repeats is a session you can trust.

  1. Warm up with a short club. A 7 iron is easiest on the unit and the net.
  2. Hit ten shots from the same tape mark. Same ball, same mat, same unit position.
  3. Drop the one mishit and average the nine. A carry of 152, 155, 154, 149, 156, 153, 155, 151 and 154 yards, minus the 149, averages about 154 yards.
  4. Check the unit before you blame the swing. A gap of 10 yards between two days is a placement or ball-marking problem first.
  5. Save the session. Every maker's app stores it, and the free tiers differ in what they show.

How do you use a golf simulator on top of that? Add the screen, the projector and the software after the launch monitor repeats. The best launch monitor page lists the units, and the home simulator page covers the whole room.

Common mistake : placing the unit by eye

A tape measure takes 30 seconds. Pacing off 7 ft gives 6 to 9 ft depending on your stride, and the Mevo Gen2 maker warns that under 16 ft of total depth tracking can be inaccurate. Measure, then mark the floor.

Questions about how to set up a launch monitor indoors

People ask a handful of practical things after they have read the manuals. The answers below stay inside what the makers write.

How to build your own launch monitor?

We found no maker or official guide for building one, so we give no steps. A home build usually means the net, the mat and the screen around a purchased unit, and the DIY golf simulator guide covers that part. A radar or camera sensor itself is a manufactured product with its own radio rules, and nothing on this page tells you how to build one.

How much does an indoor golf simulator cost?

A launch monitor is one part of the cost, and this page prints no product price. The yearly plans are printed by the makers and are on our subscription costs page; the total for a room is on our golf simulator cost page. For the shortlist of whole setups, see the best home golf simulator page.

How far behind the ball should a launch monitor be?

It depends on the type: 4 to 5 ft for the Shot Scope LM1, 4.5 to 5 ft for the SC4 PRO, 6 to 8 ft for the R10, 6.5 to 8.5 ft for the MLM2PRO and 8 ft for the Mevo Gen2. Camera units go beside the ball instead.

Do I need to level a launch monitor?

Garmin says the R50 compensates for uneven surfaces, so leveling is not required. For the R10 it asks for the unit on the ground, with its bottom edge above a mat. Voice Caddie wants its base level with the top of the hitting surface, and Bushnell wants the Launch Pro raised to the mat's level.

Is there a recall or a radio rule for launch monitors?

We searched the CPSC recall database on November 16, 2026 for launch monitors, golf, and the makers named here, and found no launch monitor recall; the search matches words, so look up the exact model on cpsc.gov before you order. The radars write only "24 GHz". The U.S. rule for field disturbance sensors in the 24.075 to 24.175 GHz band, 47 CFR 15.245, caps the field at 2,500 millivolts per meter at 3 meters, and it names no launch monitor.

Does lighting affect a launch monitor?

Garmin says it does, for direct sun on the front of the unit and on the club face. For the other makers we read, no lighting figure is written.

Sources

  • Garmin, Approach R10 owner's manual: 6 to 8 ft behind, 8 ft to the net, 2 x 2 ft hitting area, sunlight, read November 16, 2026.
  • Garmin, Approach R50 manual: 1.5 ft beside the tee, no leveling, sticker, read November 16, 2026.
  • Rapsodo, golf FAQ, MLM2PRO section and ceiling height article: distances, Net and Range modes, plans, ceiling, read November 16, 2026.
  • FlightScope, Mevo Gen2 and indoor use guide: 8 ft behind, 16 ft total, stickers, electronics, read November 16, 2026.
  • SkyTrak, Plan Your Space: beside the ball, ceiling, width, depth, Driver Test, read November 16, 2026.
  • Bushnell Golf, Launch Pro buyer's guide: 2 ft beside, 13 ft deep, 6 ft wide, read November 16, 2026.
  • Shot Scope, LM1 user guide: 4 to 5 ft behind, interference, net and ceiling rules, read November 16, 2026.
  • Voice Caddie, FAQ: 5 ft behind, 9 to 10 ft to the net, level base, read November 16, 2026.
  • Foresight Sports, complete golf simulator room setup: projector lumens and lighting, read November 16, 2026.
  • U.S. Consumer Product Safety Commission, recall database: launch monitors, makers named here and the BenQ GV31 projector, searched November 16, 2026.
  • eCFR, 47 CFR 15.245: 24 GHz field disturbance sensors, official text.
  • Amazon.com product page for the PRGR HS 130-A: batteries, memory, club head speed with or without a ball, read November 16, 2026.

Our scores are the total of six marks out of 10 per unit, taken from the wording of the maker pages and each Amazon.com listing, and nothing else. We use no customer rating; see our methodology. The depth sums are our addition of each maker's printed distances.

FlightScope Mevo Gen2FlightScope Mevo Gen2
Check my roomSee it on Amazonaffiliate link